Please fill out the following form to submit a Request for Quote to any of the following companies listed on
Goto SBT to know more.
This article will take an in-depth look at timing belts.
The article will look at timing belt topics such as:
This chapter will cover the definition of timing belts, their design, and their function.
A timing belt is composed of rubber and features hard teeth designed to interlock with the cogwheels of camshafts and crankshafts. This critical component in an internal combustion engine ensures the synchronized rotation of the camshaft and crankshaft, facilitating the precise opening and closing of engine valves during both the intake and exhaust strokes of each cylinder.
In an interference engine, the timing belt also plays a crucial role in preventing the piston from colliding with the valves. Typically, a timing belt is a toothed belt with teeth on one or both sides of its surface.
There are two main components of a timing belt: the molded cords inside the timing belt for carrying the torque load and the plastic compound used to shape the teeth and cover the cord itself. These components are available in different types of materials for different types of timing belts. To determine the type of materials to use, one has to consider the end use of the belt. Timing belts' cords are usually made out of fiberglass, polyester, or Kevlar. They transmit power in the drive system through the belt.
The cord and teeth of a timing belt are oriented at right angles to each other, allowing the cord to effectively transmit power linearly. An example of a belt designed to handle substantial loads is the serpentine belt used in automobile engines. In smaller drive systems, belt elongation is minimal due to the high strength of the cord materials relative to the loads they bear.
In small drive applications, belt stretch is virtually nonexistent because the cord materials are sufficiently robust for the loads they handle. Excessive loads can lead to cord breakage or cause the belt teeth to skip or cog over the pulley teeth. During the manufacturing of timing belts, a mold is used where plastic is injected around the pre-wound cord and precisely cut tooth profiles.
Each timing belt length requires a specific mold that includes the exact number of teeth needed for the finished belt. This ensures the production of a continuous belt with no beginning or end. Molds can produce sleeves up to 36 inches wide with the desired number of teeth, which are then trimmed to the required belt widths using specialized slitting tools. For food processing applications where FDA standards must be met, urethane belts are used because they can be colored or left clear, reducing the visibility of particles. In contrast, black neoprene belts do not offer this advantage.
Neoprene is the standard material for timing belts due to its excellent wear characteristics and its ability to accurately maintain the tooth profile from the mold. To further reduce wear, neoprene belts are often covered with a nylon fabric facing. For applications requiring minimal dust or particles, such as office copiers, clean rooms, or medical environments, engineered polymers are preferred. EPDM polymer is used as a core material, with nylon-coated tooth wear surfaces to produce less dust compared to neoprene and ensure long-lasting accuracy of the tooth profile.
Robust timing belt teeth are crucial for maintaining synchronization between the crank and cam shafts, and they come in a variety of metric pitches. Pitch refers to the distance between the centers of two adjacent teeth on a timing belt. This measurement affects other factors of timing belt pulleys, including the number of teeth and the diameter. Traditionally, timing belts were designed with trapezoidal-shaped teeth for their tooth profiles.
New manufacturing techniques have introduced curved teeth designs to address the noise and lifespan issues commonly associated with trapezoidal-shaped teeth. Additionally, timing belts with a reduced width can offer enhanced performance by decreasing weight and friction.
The arrangement of timing belt teeth varies widely depending on the specific application and environmental conditions.
As previously mentioned, the trapezoidal tooth arrangement is one of the earliest designs, while more modern timing belts use curvilinear tooth profiles.
Trapezoidal teeth are highly effective for transmitting forces. However, they tend to wear out quickly under high torque and speed conditions due to their blunt shape. Despite these drawbacks, trapezoidal teeth remain popular, especially for precision conveying and linear positioning belts, where they are often the primary choice.
Curvilinear toothed timing belts feature a smoother, more rounded tooth shape, which helps reduce tension loss and alleviate the high force concentration seen with trapezoidal teeth. Despite these advantages, curvilinear timing belts have their own drawbacks. They are more susceptible to backlash, which occurs when there is excessive play between the belt teeth and the pulley grooves. This backlash can lead to less accurate positioning and potentially reduce the overall performance of the timing belt.
These belts aim to combine the advantages of both curvilinear and trapezoidal tooth profiles. Modified curvilinear belts feature shallower tooth depths and steeper sides, allowing them to effectively transmit higher speeds and torque while maintaining durability. As a result, they are often the preferred choice for demanding industrial applications.
The stages in designing timing belts typically include:
The first stage involves determining the peak torque for the drive, which is usually the starting torque of the motor. Additionally, it is important to account for any momentary or shock loads that may occur during normal operation.
The second stage involves determining the diameters of the largest pulleys that can be used, taking into account space limitations and the system's drive ratio. This step helps increase the drive's torque capacity and extends the service life of the belt.
The third stage involves selecting the tooth profile of the belt. If the selected profile's torque capacity is near the upper limit for torque transmission, consider choosing the next higher torque-rated profile. Determine the pitch for the chosen profile, as this value is needed to calculate the required number of belt teeth.
Calculate the Teeth in Mesh (T.I.M.), taking into account the teeth in mesh factor. Divide the peak torque from the first stage by the T.I.M. factor to determine the design torque. It is also crucial to verify the belt pitch again to ensure that the adjustment in torque has not moved your application outside the desired pitch limits for the selected pulleys.
This stage involves calculating the belt pitch length based on the distance between the design centers of the drive components.
The sixth stage involves dividing the belt pitch length by the selected tooth pitch and rounding the result to the nearest whole number. This number represents the total teeth on the belt for the application. Additionally, the nominal center distance of the drive design must be adjusted to match the belt.
The seventh stage involves calculating the effective tension (Te) in the drive. This is done using the pitch radius and design torque of the smallest loaded pulley in the system.
In this stage, select the strength factor for the application. Divide the effective tension calculated in stage seven by this strength factor to determine the required break strength for the belt design. For a double span break, multiply the result by 2. Consult the table to determine the required reinforcement type and belt width, ensuring that the listed value exceeds the calculated break strength for the design.
This stage involves selecting a belt width that can handle the design torque with the chosen pulley size. It is important to ensure that the required belt width for the system is the wider of the two options considered.
The length of the belt can be calculated using the known pulley diameter and the center-to-center distance between the driven pulley and the driver.
The formula to calculate the length of the belt is as follows:
Length of belt = 2L + 1.57d' + d' - (d' - d')² / 4L
Where:
d' and d' are the diameters of the timing pulleys,
L is the distance between the centers of the timing pulleys.
The materials commonly used in constructing timing belts include:
Rubber is the most widely recognized material for timing belts used in various industries and applications. Many internal combustion engines in a wide range of vehicles rely on timing belts made from rubber or rubber compounds. Despite its popularity, rubber as a timing belt material has some limitations.
Rubber timing belts are known for their tendency to stretch and break quickly when exposed to high temperatures and motor oil in engine blocks. However, advancements in technology have led to the development of temperature-resistant rubber materials that enhance the lifespan of timing belts and improve their resistance to distortion.
Modern rubber compounds and reinforcing fibers provide greater strength and traction. These enhanced materials also protect against sheared teeth and other potential damage to the belt.
Polyurethane has become a popular choice for timing belts due to its high temperature resistance, superior elasticity, and resistance to oil damage. Timing belts made from polyurethane are durable and provide highly energy-efficient solutions for a wide range of applications.
Polyurethane belts offer high tensile strength and increased loading capacities, which are essential for generating optimal torque. They are favored in the industry for their ease of cleaning and maintenance. Due to these advantages, polyurethane is often the material of choice for timing belts used in various power transmission systems and roller conveyor systems.
Fabric timing belts are ideal for applications requiring high performance and acceleration forces. They are made from a variety of materials, resulting in excellent tensile strength, low friction coefficients, and superior resistance to both high and low temperatures. For applications with demanding requirements, such as high torque or rapid acceleration, fabric timing belts offer a diverse range of options that provide significant benefits.
Timing belts are crucial for the operation of a vehicle's engine, connecting the camshaft to the crankshaft and controlling the pistons and valves. In simple terms, a timing belt is a reinforced rubber belt with teeth or notches on its inner side.
The timing belt ensures precise synchronization of the engine's valve openings and closings. As the crankshaft turns, it drives the timing belt, which in turn rotates the camshaft. This movement opens and closes the valves, allowing the pistons to move up and down. For example, in a four-stroke engine, there are four phases: intake, combustion, compression, and exhaust. During the intake phase, air and fuel enter the cylinders while the intake valves are open and the exhaust valves remain closed.
During the combustion and compression phases, the air-fuel mixture is compressed and ignited by the spark plugs, with all valves remaining closed. In the final exhaust phase, the remaining gases are expelled through the exhaust valve, while the intake valves stay closed. The timing belt plays a crucial role in managing the precise opening and closing of the valves and the pistons' movement throughout each phase, ensuring that each step occurs in the correct sequence.
This chapter will explore the different types of timing belts and the potential causes of their failure.
The types of timing belts include:
Open-ended timing belts come in various materials, including extruded thermoplastic polyurethane. These belts are dimensionally stable, making them ideal for linear drive systems due to their precise positioning capabilities.
Open-ended timing belts exhibit a high spring rate and excellent tooth shear strength. For linear drives requiring high stiffness and repeatability, steel tension members are preferred over aramid fiber. The Move-Series AT10 or AT15 are the stiffest and strongest options available. These belts come in 50-meter rolls or can be cut to specified lengths.
For many general-purpose applications, spliced and welded timing belts are commonly used. These belts are preferred for conveying, as well as for profiles and backings that require welding. The construction process involves starting with a length of roll stock, which is open-ended and features finger splices cut into the belt. These splices are then welded together using heat to form a continuous belt.
Spliced and welded timing belts feature the same sealed edges and smooth back as open-ended timing belts. Despite being welded, they retain about 50 percent of the strength of truly endless belts. These belts can be purchased in one-tooth increments for minimum lengths.
Truly endless polyurethane timing belts are extruded without any welds, making them the strongest construction type. This characteristic makes them particularly suitable for power transmission applications. These belts typically include steel tension members and are available in various materials.
For more information, please visit Automotive Timing Belts.
The AT tooth configuration is widely recognized for its enhanced tooth shear strength. Double-sided timing belts are available for drive systems with changing shaft directions. These belts may have unsealed edges, and upon close inspection, a pin-hole may be visible where the tension member exited the belt during the extrusion process.
Manufacturers recommend specific intervals for timing belt replacement, usually between 30,000 to 50,000 miles. Failure to replace the timing belt on time can lead to a complete engine breakdown or catastrophic failure, especially in interference engines. It's essential to consult the vehicle's maintenance manual for the appropriate replacement intervals.
It's common to replace the timing belt tensioner simultaneously with the belt. In some engines, where the timing belt also drives the coolant pump, the coolant pump is often replaced as well. Common timing belt failure modes include delamination and unraveling of the fiber cores or stripped teeth. Stripped teeth cause the belt to slip on the drive cog. Although timing belt breakage is rare due to the high tensile strength of the fibers, the belt can wear prematurely from debris mixed with oil and grease.
Proper belt tension is crucial for the timing belt's longevity. A belt that is too loose will whip, while one that is too tight will cause whining and excessive strain on the cog bearings, both of which significantly shorten the belt's lifespan. Additionally, failures in the belt tensioner, gear, or idler bearings can cause the belt to derail.
When replacing a timing belt, careful attention must be paid to ensure proper synchronization of valve and piston movements. Incorrect synchronization can lead to valve timing issues, resulting in collisions between valves and pistons in interference engines.
The various causes of timing belt failure include:
One of the primary causes of timing belt drive failure is misalignment. This can result from uneven or excessive tooth wear, tensile failure, and improper belt tracking. To extend the lifespan of your timing belt and minimize downtime, ensure that your shafts and timing pulleys are properly aligned.
Excessive load is a common cause of tooth shearing in timing belts. Such loads or shock loads can also lead to uneven and excessive tooth wear, as well as tensile failure. To address this issue, it is necessary to redesign the drive system to better handle the load.
Ratcheting, or the skipping of teeth, occurs when a timing belt is under-tensioned. This condition leads to excessive or uneven wear of the teeth and increased drive noise. To ensure proper tension, use a tension gauge to adjust the timing belt accordingly.
Excessive vibration or noticeable belt stretch in a timing drive may indicate a weak drive structure. To address this issue, reinforce the drive structure to stabilize performance and prevent further problems.
Damaged or worn pulleys can significantly reduce the lifespan of a timing belt. Worn teeth on the pulleys can cause the belt to wear unevenly or become damaged. Nicks or gouges on the pulleys can also cut into the belt. Regular inspection and timely replacement of any worn or damaged pulleys are essential to maintain the integrity of the timing belt.
Debris is often an overlooked cause of timing belt failure. Dirt and rust can abrade the belt and oil can damage the belt materials. To prevent such issues, clean the pulleys and timing belt regularly with a stiff brush to remove rust and dirt, and wipe off any oil or grease. Additionally, fitting a shield to the drive can help protect against debris and extend the lifespan of the timing belt.
The various symptoms that indicate a timing belt is nearing failure include:
If you hear only the starter motor engaging but the engine does not turn over when you turn the key, it may be a sign that the timing belt is failing.
A broken timing belt may cause a continuous ticking or clicking sound coming from the engine.
Misfiring is a common issue with malfunctioning timing belts. If the belt slips on the camshaft drive, it can cause the engine's cylinders to open or close prematurely, affecting the engine's firing rate.
These noises might occur only when the vehicle accelerates or when braking, in contrast to a constant ticking sound that persists regardless of the vehicle's speed or braking status.
This chapter will discuss the applications of timing belts, including their advantages and disadvantages when compared to flat or round belts. Considerations when selecting timing belts will also be discussed.
Timing belts are used in a range of applications, including:
Timing belts are integral to the timing belt and cam belt systems found in most automobiles worldwide. The efficiency of these timing belts is crucial to the mobility of the modern world, as they ensure the smooth operation of vehicles. Automotive timing belts are high-performance, toothed belts designed for precision.
These belts are made from specialized materials to synchronize the rotational motion of the engine's crankshaft with its camshaft. This synchronization is essential for the proper opening of the intake and exhaust valves in the engine's combustion chambers at the exact moments of expansion or compression. Proper coordination is vital for sustaining the engine's combustion process and maintaining its performance. If the timing belt fails, combustion cannot occur effectively.
Timing belts must maintain precise synchronicity and perform reliably at high rotational speeds. They need to be robust enough to withstand high temperatures and operate effectively in the varied conditions encountered on the road.
A notable example of a belt-driven system is the treadmill. It's important not to confuse the timing belt with the tread on which the runner runs. The timing belt in this context refers to the toothed, synchronous belt that transmits rotary motion from the central motor to the drive pulley. Typically located at the rear of the treadmill, though sometimes at the front, this timing belt is crucial for the treadmill's operation. Both flat friction timing belts and toothed belts can be used in treadmills.
A sewing machine is a common example of a belt-driven system. In this case, the timing belt transfers motion between the sewing pulleys and the motor. While it may not operate under the high performance and load conditions of systems like treadmills or automobiles, it effectively demonstrates the use of synchronous timing belts. The belt system in a sewing machine transmits the rotary motion from the main drive motor to the larger spool head, which then powers the sewing mechanism.
Timing belts are also utilized in 3D printers, conveyor systems, CVT automatic transmission and industrial automation products.
When comparing timing belts to flat or round belt drives, they may have certain disadvantages, such as:
However, these disadvantages are outweighed by the benefits which include:
When selecting a timing belt, several considerations should be taken into account, including:
Clearly seen, there are many different materials used in timing belts due to their own different specifications to which they can handle certain circumstances. As already mentioned earlier, the different types of materials for timing belts include urethane, neoprene, rubber, fabric etc. Each material has its own unique properties that make it the most suitable for a particular application.
In addition to the type of material, several other characteristics must be considered when choosing a timing belt, as these factors affect the smooth operation of the equipment. These characteristics include:
Belt width influences the potential tracking force of the timing belt. Wider timing belts generate greater tracking forces, enhancing their capability to handle higher loads.
Shorter belts exhibit greater tracking forces due to the stronger connection between the tensile cords and the belt molds.
Smaller pulleys generate higher tracking forces. To ensure proper operation, the diameter of the pulley should be larger than that of the belt.
The magnitude of the belt installation tension is crucial due to the impact of various torque loads experienced by the timing belt during operation. Proper tension ensures effective belt tracking and performance.
Timing belts are quite delicate and can be easily damaged if the operating environment is harsh. Factors such as dust particles can interfere with their function, potentially leading to malfunctions in the timing belt system.
The performance of a timing belt is highly dependent on its application. Not all materials are suitable for every industry's requirements, so it is essential to choose a timing belt that matches the specific demands of the application.
This pertains to selecting between a standard design or a custom design for the timing belt. The choice of design depends on the level of precision required for the application.
Timing belts come in many different types with each type suitable for a certain application. Each timing belt is made out of a specific type of material that makes it perform best in a certain or particular environment. If you are to choose a timing belt for a particular application, always consider the type of material it is made from. This ensures optimal results in the performance of the timing belt for the particular application you choose it for. The replacement of a timing belt is also critical and time reliant.
What is a timing belt? A timing belt is a cogged rubber belt that connects the camshaft and crankshaft of an engine. The crankshaft is spun by the pistons via connecting rods, sort of like the crank on a bicycle is spun by your legs. The camshaft must open valves at certain points in the pistons' travel, so the camshafts' rotation must be synchronized to the crankshaft's rotation. This is why the timing belt has cogs. The bumps in the timing belt fit into cogs in the cam and crank sprockets to prevent slippage.
Do all cars have timing belts? No. Some cars have a timing chain that connects the cam and crank sprockets and others have timing gears that connect directly.
When should I replace my timing belt? The manufacturer usually publishes a mileage/time interval for timing belt replacement, however, for some makes and models it's not always clear, logical, or the best time.
Some examples:
Not clear: When the Acura was introduced there was no mileage or time interval published. (Later Acura recommended a 90K mi. 7.5-year interval)
Not logical: Some Mazda cars have a 105K mile interval for federal cars, but a 60K interval for California cars, even though the engine design and the timing belt part number are the same.
Not the best time: Most pre- Toyota cars have a 60K mi. interval, yet the timing belts will easily last until 80K.
So, when should you replace your belt? When in doubt, use the published interval (if there is one). Give us a call with the year and model of your Acura, Honda, Mazda, Nissan, or Toyota, Audi, Hyundai, Subaru or Kia and we'll be happy to let you know the manufacturer's specifications or give you our opinion based on our past experience with your vehicle's model.
Should I replace the water pump with the timing belt? Maybe. There are a lot of variables involved! The right time to replace the pump depends on your individual vehicle ' the make, model, and how many miles are on it. It also depends on the type of water pump your car uses and whether it's rotated by the timing belt; if it is, then it's definitely a good time to do it, plus having it done now can save you money in the long-run. If the water pump is blocked by the timing belt (in other words ' you must remove the timing belt to remove the water pump), then yes; it will save you money, time, and hassle. If the water pump can be replaced without removing the timing belt, then it's not necessary to replace the water pump unless it's worn or leaking. If the water pump is easier to replace when the timing belt is off, then you may want to consider replacing it since your vehicle is already in the shop. There's also the question of cost; can you afford to do it now, while your vehicle is already in the shop, or would it be easier on your budget to come back in six months or so?
Should I replace the cam seal / crank seal / oil pump seal / oil pump O-ring? If the seals are leaking at all, then it's a perfect time to replace them. They're much easier to get to while we're working on the timing belt, and it's less expensive for you. Getting the leaking seals replaced will also prevent the possibility of needing to replace the timing belt again in the near future.
Should I replace the timing belt tensioner / idler? If either of them is damaged or worn down, then they should be replaced to prevent any damage to your new timing belt. Depending on the mileage of your vehicle or the condition of the belt tensioner/idler, you may want to have them replaced as preventive care since there's no additional labor charge when they're replaced along with the timing belt. It's a convenient time to change them, however, it may not be necessary.
Should I replace the accessory drive belts? If the belts are worn down or cracked, then yes. If they're still in good shape, they can be replaced at any time without removing the timing belt.
Does it make a difference what brand of part I use? Not necessarily. We work closely with our customers and always give them a choice on the parts used. We'll explain the pros and cons of the different brands so you can make the most informed decision possible. We use quality parts, regardless of brand, and will always offer the best solution to fit your needs and budget. We provide a 3 year/36,000 mile warranty on all parts and labor, so no matter which part you choose, you can always feel confident in the quality of our repairs and part selection. If you have any questions or would like to schedule an appointment, give us a call at 253-854-. We're always happy to help!
Are you interested in learning more about Audi Timing Belt Replacement? Contact us today to secure an expert consultation!